SPD commands:
array 12345 # only show antennas 1, 2, 3, 4 and 5
acs # show auto-correlations
noacs # do not show auto-correlations
on fx # show IFx where x is either 1 or 2
off fx # do not show IFx
chan # plot all channels
chan n1 n2 n3 n4 # select channel ranges for IF1 (n1 - n2) and IF 2 (n3 - n4)
(see also http://www.csiro.atnf.au/observers/docs ... start.html" onclick="window.open(this.href);return false; by Kate Brooks & Vince McIntyre)
Pages at http://www.narrabri.atnf.csiro.au/opera ... /corr.html" onclick="window.open(this.href);return false; are out-of-date
SPD
Moderator: Mark.Wieringa
-
- Site Admin
- Posts: 220
- Joined: Thu Feb 04, 2010 3:27 pm
- Location: Paul Wild Observatory Narrabri NSW
Re: SPD
Hi Baerbel,
Good start! I'll contribute some more information:
[on/off] acs: turn on/off display of auto-correlation spectra
[on/off] ccs: turn on/off display of cross-correlation spectra
[on/off] fn: turn on/off display of spectra from IF n (where n is a number between 1 and the number of IFs available)
sel [nm]pq: select spectra formed between polarisations p and q on baselines with both antenna n and m (if specified), where both p and q are one of a or b, and n and m represent the available antennae; note that one can specify more than one selection at a time, ie. "sel 12aa 24aa 36bb 56ab"
ch fn chan1 chan2: change the display of IF n to display only channels between chan1 and chan2, eg. "ch f2 513 1537" will display data between channels 513 and 1537 for all IF 2 spectra
sca mode: change the scaling mode of the amplitude axis, where mode is lin (for linear scaling) or log (for log scaling)
x: change between displaying the channel number and the frequency on the x-axis
p: display phases
a: display amplitudes
auto: turn on time averaging of the SPD display
noauto: turn off time averaging
write [file]: writes a Postscript file of the current display to the current directory (the command will also tell you what file it created). If file is not specified, then a generic filename that includes the current time will be used.
Remember that SPD will only ever show 16 or fewer panels in its PGPLOT window, where each panel represents a single baseline and either an auto-correlation or cross-correlation. It will preferentially display the lowest numbered IF first, so panels from IF 1 (if it is enabled) will always be displayed before panels from IF 2, etc. It will then preferentially display the auto-correlations first within each IF, if they are enabled.
Something to be aware of is that when displaying auto-correlations, SPD will show two different-coloured spectra for each polarisation product aa and bb. These different colours show the power when the noise-diode in the receiver is on or off. Also note that selecting a cross-polarisation product will only work when viewing the auto-correlations, even though the correlator is actually computing cross-polarisations for all baselines.
Good start! I'll contribute some more information:
[on/off] acs: turn on/off display of auto-correlation spectra
[on/off] ccs: turn on/off display of cross-correlation spectra
[on/off] fn: turn on/off display of spectra from IF n (where n is a number between 1 and the number of IFs available)
sel [nm]pq: select spectra formed between polarisations p and q on baselines with both antenna n and m (if specified), where both p and q are one of a or b, and n and m represent the available antennae; note that one can specify more than one selection at a time, ie. "sel 12aa 24aa 36bb 56ab"
ch fn chan1 chan2: change the display of IF n to display only channels between chan1 and chan2, eg. "ch f2 513 1537" will display data between channels 513 and 1537 for all IF 2 spectra
sca mode: change the scaling mode of the amplitude axis, where mode is lin (for linear scaling) or log (for log scaling)
x: change between displaying the channel number and the frequency on the x-axis
p: display phases
a: display amplitudes
auto: turn on time averaging of the SPD display
noauto: turn off time averaging
write [file]: writes a Postscript file of the current display to the current directory (the command will also tell you what file it created). If file is not specified, then a generic filename that includes the current time will be used.
Remember that SPD will only ever show 16 or fewer panels in its PGPLOT window, where each panel represents a single baseline and either an auto-correlation or cross-correlation. It will preferentially display the lowest numbered IF first, so panels from IF 1 (if it is enabled) will always be displayed before panels from IF 2, etc. It will then preferentially display the auto-correlations first within each IF, if they are enabled.
Something to be aware of is that when displaying auto-correlations, SPD will show two different-coloured spectra for each polarisation product aa and bb. These different colours show the power when the noise-diode in the receiver is on or off. Also note that selecting a cross-polarisation product will only work when viewing the auto-correlations, even though the correlator is actually computing cross-polarisations for all baselines.
cheers
Jamie Stevens
ATCA Senior System Scientist
Jamie Stevens
ATCA Senior System Scientist
Re: SPD
Hi Jamie,
Do you (or anyone else for that matter) know if there is a way to tell which mode the x-axis is currently in i.e. channel or frequency? It can sometimes get really confusing at 20 cm trying to work out whether something is a channel or a frequency (particularly when sleep deprived) and as the "x" command is a toggle you never quite know which state it is currently in (from what I remember there wasn't any obvious label for the x-axis to help with this).
Cheers,
Emil.
Do you (or anyone else for that matter) know if there is a way to tell which mode the x-axis is currently in i.e. channel or frequency? It can sometimes get really confusing at 20 cm trying to work out whether something is a channel or a frequency (particularly when sleep deprived) and as the "x" command is a toggle you never quite know which state it is currently in (from what I remember there wasn't any obvious label for the x-axis to help with this).
Cheers,
Emil.
-
- Site Admin
- Posts: 220
- Joined: Thu Feb 04, 2010 3:27 pm
- Location: Paul Wild Observatory Narrabri NSW
Re: SPD
Hi Emil,
As far as I know, there isn't a way of telling which mode SPD is in.
The only band it is really a problem at is at 20cm as you said, and then only when one is zoomed in on a particular frequency range. One thing to remember here is that the 20cm band is frequency inverted, so when the entire band is being viewed in SPD, which will have a central frequency of 1750 MHz, the usable band will appear above the centre in channel mode, and below the centre in frequency mode. I guess that's one way to be sure.
As far as I know, there isn't a way of telling which mode SPD is in.
The only band it is really a problem at is at 20cm as you said, and then only when one is zoomed in on a particular frequency range. One thing to remember here is that the 20cm band is frequency inverted, so when the entire band is being viewed in SPD, which will have a central frequency of 1750 MHz, the usable band will appear above the centre in channel mode, and below the centre in frequency mode. I guess that's one way to be sure.
cheers
Jamie Stevens
ATCA Senior System Scientist
Jamie Stevens
ATCA Senior System Scientist